Are you hunting for answers on A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately tough job. If the old bathtub is conveniently accessible, the task can relocate speedily; if you have to open up a wall surface to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will need a helper to move out the old tub and set in the brand-new one. Make certain you have certified on your own for the job and also fit trying it. Rather than hiring a service provider to take over a halfway-completed task, it is better to think about employing one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This short article will aid you mount a brand-new tub in your restroom if you have already bought a new tub and don't require to alter the setup of your previous water supply pipelines.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be rather problematic due to the limited access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the tap and the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The former type should be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, put the tub in the called for position. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bathtub up until the spirit level reviews degree.
To mount faucets, fit all-time low of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply and also examine all joints as well as brand-new pipework for leakages and also tighten them if required. Load the tub as well as also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the bath tub has actually been utilized a minimum of once as this will certainly settle it into its final placement.
Planning for the Setup
Firstly, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its final position.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a stiff seal, causing the water to permeate the wall surface between the bathroom and the tiling, leading to issues with dampness and feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always load the bathtub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack rather very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently offered on the market. It is recommended to fit the tiles making use of water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that write up on How to Install a Bathtub Yourself while doing a lookup on the internet. So long as you enjoyed our blog entry if you please don't forget to pass it around. Many thanks for your time. Kindly come by our website back soon.
Let's solve it, call now!